A DIY sex doll stand is another great but easy way to maintain your doll in the good condition that she needs to be in. By having a sex doll stand you are assured of no creases, or flat spots or damages occurring to your doll through storage. A step by step guide to making your own DIY sex doll stand follows:
Brand: Irontech Doll
Materials Needed
PVC pipes (various sizes)
PVC pipe connectors (elbows, tees, caps)
PVC pipe cutter or hacksaw
Measuring tape
Sandpaper
Drill with appropriate bits
Screws and nuts
Plywood or MDF board (for base)
Soft padding (foam or cloth)
Paint (optional)
Here’s how to construct it step-by-step:
1. Design The Stand: Sketch out a basic design for the stand. It will need to hold the doll by its arms, back and possibly the legs to prevent her from tipping forwards and backwards.
2. Measure and Cut PVC pipes:
* Measure the Doll: Take the doll and measure it to determine the proportions needed for the stand. You will need to measure from where the stand will rest up to just below the dolls arms and also her shoulder width. For the width of the stand, measure the depth of the doll.
* Cut the Pipes: Once you have measurements you can begin cutting the PVC pipes to the required size for vertical supports, horizontal supports for the arms, and the base structure. While you may wish to buy pre-cut PVC joints for the elbow and T fittings, you will need some lengths of PVC pipe to assemble it with.
3. Build the Base Frame:
* Form the Base: When you begin constructing, always make sure you form a stable and strong base using PVC pipes and fittings. A rectangle shape will always be best but an H shape may provide extra support if necessary.
* Connectors: The pipes will need to be secured by using T-shaped and elbow joints, ensure they fit securely within the PVC pipe.
4. Build the Vertical Support:
* Attach Vertical Pipes: Secure the vertical supports by screwing or pushing them into the T joints within the base. Now attach another horizontal support pipe that goes between the top of each of the vertical pipes – this will be the part the dolls arms support themselves against – using an elbow connector for each side of the structure.
* Add Cross Supports: Add more cross supports depending on the rigidity needed for the vertical support. However I'd always add a horizontal pipe joining both vertical arms at their top to increase stability and provide more support for the doll's arms.
5. Add Padding for Protection:
* Soft Padding: You should always remember to add soft padding on any part of the frame that touches the doll, this will prevent any indentation damage, or any scratches being made to her skin. Foam or cloth padding is very common and can be purchased from any hardware store and can easily be taped or stuck onto the relevant areas of the stand.
* Secure Padding: To prevent the padding falling off use either strong adhesive tape, glue or simply tie it on with rope to the framework of the stand.
6. Create the Head and Neck Support (Optional):
* Neck Support: If you wish to secure the dolls head and neck then you can do so in a similar fashion, by adding a horizontal pipe around the highest point and padding it so the dolls head does not flop and cause damage/markings to the skin.
* Adjustable Support: Consider adding an adjustable PVC fitting where the neck support connects to allow the correct angle for the head to be displayed in so it looks more natural.
7. Attach the Base Platform:
* Base Platform: Use MDF or plywood cut to fit the width of the frame to provide a stable base and stop the stand from tipping forward and backward. The base platform will also keep the doll's legs from catching on the framework of the stand. The size of this plate is important so use careful measurements; once cut it can either be screwed into the bottom horizontal pipe using an ordinary screw from the top, or it can be held in place with a PVC fitting placed underneath that clips over the bottom pipe.
* Secure the Base: When screwing the base plate into the base of the frame, be sure not to screw through any of the joining fittings but always use the solid length of the pipe frame to screw into and the screws should also be counter sunk so they sit flush with the base plate, to avoid marking or damage to the doll.
8. Final Assembly and Adjustments:
* Final Check: Once the frame is built, it's essential to double-check the entire structure. Make sure that nothing can move freely, or if necessary strengthen any joints with more screws or an adhesive/binding substance; the frame must be incredibly strong. Check that the doll is properly seated on the stand and can stand naturally at the correct posture by adjusting parts or padding where necessary.
* Paint (Optional): The frame can be left in the standard PVC colour but if you want to give it more of a professional finish, then apply a coat of gloss spray paint.
Safety Tips
* Stability: Ensure that the base of the frame is always a wide, stable surface so it cannot be knocked over easily.
* Padding: Always pad the part of the stand which is in contact with the dolls skin and periodically check that the padding isn't damaged and is protecting the doll sufficiently.
* Regular Maintenance: Frequently inspect the stand to ensure that no part of the construction is loose and no joints are weakening. Make sure any loose or damaged parts are immediately secured or replaced so there is no potential for disaster.
Conclusion
Making a sex doll stand is a cheap and resourceful way of ensuring that your sex doll remains supported at all times which is crucial for protecting your doll from injury. A correctly built stand can ensure that your dolls life span is increased and its appearance will be maintained for years to come. If you construct the stand carefully, so that it remains stable and well-padded, your sex doll can remain supported, and by periodically testing its strength and integrity, you can maintain the stand's excellent condition.
